使用wpa supplicant连接无线：修订间差异
小无编辑摘要 |
小无编辑摘要 |
||
| 第63行： | 第63行： | ||
=== 啥玩意？ === | === 啥玩意？ === | ||
==== | ==== 1 for AP that doesn`t have encryption ==== | ||
>add_network (It will display a network id for you, assume it returns 0) | >add_network (It will display a network id for you, assume it returns 0) | ||
| 第74行： | 第74行： | ||
>quit | >quit | ||
==== | ==== 2 for AP that has WEP ==== | ||
>add_network (assume returns 1) | >add_network (assume returns 1) | ||
| 第95行： | 第95行： | ||
>enable_network 1 | >enable_network 1 | ||
==== | ==== 3 for AP that has WPA-PSK/WPA2-PSK ==== | ||
>add_network (assume returns 2) | >add_network (assume returns 2) | ||
2018年12月14日 (五) 22:14的最新版本
使用 wpa_supplicant的客户端工具wpa_cli连接无线
wpa_supplicant包含两个主要的可执行工具：wpa_supplicant和wpa_cli。wpa_supplicant是核心程序，它和wpa_cli的关系就是服务和客户端的关系：后台运行wpa_supplicant，使用wpa_cli来搜索、设置、和连接网络。
apt-get install wireless-tools
在wpa_cli交互模式下可以执行很多命令 ，使用命令
wpa_cli -h
man wpa_cli
查看相关介绍
步骤
1.运行服务端wpa_supplicant
wpa_supplicant -i<wlan0> -D<driver> -B -c </etc/wpa_supplicant/wpa_supplicant.conf>
*部分linux发行版默认wpa_supplicant服务已运行，使用top命令查询，已运行则不需要再执行此命令，-D参数部分情况下不需要
2.运行客户端wpa_cli
wpa_cli -i<ifname> -p<path to ctrl sockets>
*不使用-i参数则使用默认网卡，-p
3.扫描网络信息
scan
scan_result
4.添加启用网络
add_network
*注意回显编号
set_network 0 ssid "ssid"
set_network 0 psk "psk"
select_network 0
enable_network 0
*0为network编号
list_network
status
5.保存配置
save_config
quit
6.获取IP
dhclient <ifname>
*获取ip地址
啥玩意？
1 for AP that doesn`t have encryption
>add_network (It will display a network id for you, assume it returns 0)
>set_network 0 ssid “666”
>set_network 0 key_mgmt NONE
>enable_network 0
>quit
2 for AP that has WEP
>add_network (assume returns 1)
>set_network 1 ssid “666”
>set_network 1 key_mgmt NONE
>set_network 1 wep_key0 “your ap passwork”(if usting ASCII, it need
double quotation marks, if using hex, then don`t need the double quotation
marks)
>set_network 1 wep_tx_keyidx 0
>select_network 1 (optional, remember, if you are connecting with another
AP, you should select it to disable the another)
>enable_network 1
3 for AP that has WPA-PSK/WPA2-PSK
>add_network (assume returns 2)
>set_network 2 ssid “666”
>set_network 2 psk “your pre-shared key”
>select_network 2 (optional, remember, if you are connecting with another
AP, you should select it to disable the another
>enable_network 2
wpa_supplicant -iwlan1 -C /var/run/wpa_supplicant/ -c /etc/wpa_supplicant/wpa_supplicant.conf -B -u -s -O /run/wpa_supplicant
wpa_supplicant -iwlan1 -C /var/run/wpa_supplicant/ -c /etc/wpa_supplicant/wpa_supplicant.conf -B
配置中的坑
cat /etc/wpa_supplicant/wpa_supplicant.conf
ctrl_interface=/var/run/wpa_supplicant/
update_config=1
PS:http://blog.csdn.net/zhandoushi1982/article/details/24097775
